Airlink101 Network Router ASW324V2 User Manual

Quick Installation Guide  
24-Port 10/100Mbps  
Green Switch  
Model# ASW324v2  
Ver. 1A  
 
Introduction  
Congratulations on your purchase of the 24-Port 10/100Mbps  
Green Switch! It is an easy-to-install network switch which  
helps you to extend your network structure quickly and  
reliably. The 24-Port 10/100Mbps Green Switch is designed  
for energy saving, easy installation and high performance in  
an environment where network traffic and the number of  
users increase continuously. You can add other Ethernet  
devices like computers, IP cameras, and Network Attached  
Storage (NAS) onto your network quickly and easily. The  
Green EEE (Energy Efficient Ethernet) technology of  
ASW324v2 automatically reduces the power consumption  
when any connected port is detected inactive (idle or  
cable-unplugged) and it intelligently allocates less power to  
any port that connects with an Ethernet cable shorter than  
20m (66 ft)*.  
Before you start installation, please check the package  
contents:  
Package Contents:  
24-Port 10/100Mbps Green Switch  
Power Cord  
Quick Installation Guide  
Brackets and Screws  
2
 
Section 1  
Hardware Description  
1.1 Hardware Interface  
24 x Port 10/100Mbps auto-negotiation RJ45 port  
All ports support auto MDI/MDIX, no need to use  
cross-over cables  
1.2 Panel  
1.2.1 Front Panel  
The front panel of the Switch consists of LED indicators, and  
24 10/100Mbps ports. The figure below shows the front panel  
of the Switch.  
Figure 1-1 Front Panel View of the Switch  
10/100Mbps Ports (Port 1~24): These ports support  
10/100Mbps, and can operate in Half/Full Duplex transfer  
modes. These ports also support automatic MDI/MDI-X  
crossover detection, offering true “plug and play” function.  
LED Indicators: Comprehensive LED indicators display  
the status of the Switch and the network (see Section  
1.2.3).  
3
 
1.2.2 Rear Panel  
Figure 1-2 Rear Panel View of the Switch  
AC Power Connector: Supports AC 100~240V, 50~60Hz.  
NOTE:  
Do not cover or put anything on or surrounding the Switch  
while the Switch is operating.  
1.2.3 LED indicators information  
The front panel LEDs provide instant status feedback and  
help monitoring and troubleshooting when needed.  
Figure 1-3 Front Panel View of the Switch  
4
 
POWER: Power Indicator  
Status  
LED  
Color  
Solid  
Blinking  
Off  
The Switch is  
power-on  
POWER  
Green  
N/A  
No power  
Port 1~24 10/100Mbps Status LEDs  
Status  
LED  
Color  
Green  
Color  
Solid  
No activities  
on the  
Blinking  
The port is  
transmitting  
or receiving  
data at  
Off  
LINK/  
ACT  
10/100Mbps  
Ethernet  
network  
No link  
10/100Mbps  
Status  
LED  
Solid  
The  
Blinking  
Off  
The  
respective  
port is  
respective  
port is  
connected to  
the  
10/ 100M Green  
N/A  
connected  
to the slow  
Ethernet  
network  
10/100Mbps  
Ethernet  
network  
5
 
Section 2  
Installing the Switch  
The site where you place the Switch may greatly affect its  
performance.  
2.1 Installation  
Please follow the guidelines below to install the Switch:  
Please install the Switch in a fairly cool and dry place.  
Please refer to the Technical Specifications for the  
acceptable temperature and humidity operating  
ranges.  
Please install the Switch on a sturdy, level surface that  
can support its weight.  
When connecting the power cord to the Switch and the  
power outlet, the distance should be no more than  
182cm.  
Please leave at least 10cm (about 4 inches) of space  
at the front and rear of the Switch for ventilation.  
2.2 Desktop or Shelf Installation  
When installing the Switch on the desktop or shelf, please  
attach the rubber feet to the Switch. Peel off the protective  
paper on the pads and attach them to the bottom of the  
Switch (one at each corner).  
6
 
2.3 Rack Installation  
The Switch is rack-mountable and can be installed on an EIA  
11-inch equipment rack. To do this, first install the mounting  
brackets on the Switch’s side panels (one on each side),  
secure them with the included screws, and then use the  
screws provided with the equipment rack to mount the  
Switch.  
2.4 Power on the Switch  
The Switch has a universal power supply ranging from 100V  
to 240V AC, 50 ~ 60Hz power source. The AC power  
connector is located at the rear of the unit. The Switch’s  
power supply will adjust to the local power source  
automatically.  
7
 
Section 3  
Connecting the Switch  
This section describes how to connect the Switch to your  
10/100Mbps Ethernet network.  
Your network device (i.e. computer, switch, IP Camera, VoIP)  
can be connected to any port of the Switch via a two-pair  
UTP Category 5 Cable. If the LED indicators do not light up  
after making a proper connection, check your network device,  
the cable, the Switch conditions and connections.  
8
 
Section 4  
Troubleshooting  
1. Power LED is not on  
Check if the power adapter is properly connected to the  
power outlet. Make sure the power jack is firmly plugged  
into the power socket of the switch.  
2. Link/Activity is not lit when connect to 10/100Mbps device  
Made sure that the network device attached to the switch  
is turned ON.  
Check the network cable; make sure it is properly  
connected to the switch and the network device.  
Check the network cable; make sure the Ethernet cables  
comply with the specifications described in Section 2.  
9
 
Section 5  
Technical Specifications  
Standards  
IEEE 802.3 10BASE–T, IEEE 802.3u 100BASE–TX, IEEE  
802.3x Flow Control and IEEE 802.3az(EEE – Energy  
Efficient Ethernet)  
Network Cables  
Ethernet (10Base-T): Cables: 2-pair UTP Cat. 3, 4, 5,  
Twisted Pair (UTP). Up to 100m  
Fast Ethernet (100Base-T): 2-pair UTP Cat. 5, Twisted  
Pair (UTP). Up to 100m  
Ports  
24 x 10/100Mbps Auto-Negotiation RJ45 Port  
Access Method  
CSMA/CD  
Transmission Method  
Store and Forward  
Data Transfer Rate**  
Ethernet: 10/20Mbps – Half/Full-Duplex  
Fast Ethernet: 100/200Mbps – Half/Full Duplex  
LED  
Power: Green  
Link/Activity: Link/Activity (Green)  
10/100M (Green)  
Rack Mount  
11-Inch Rack-Mountable with mounting kits  
Dimensions  
10  
 
280mm x 165mm x 45mm (LxWxH)  
Weight  
1400g (3 lb)  
Physical and Environmental  
Power Input: 100~240V AC, 50~60Hz  
Operation Temperature: 0 °C ~ 40°C(32°F ~ 104°F)  
Storage Temperature: -20°C ~ 70°C(-4°F ~ 158°F)  
Humidity: 5% ~ 90% RH, non-condensing  
Certification  
FCC, CE  
11  
 
Section 6  
Technical Support  
Toll-Free: 1-888-746-3238*  
* Free Voice Technical Support is only available within the hardware warranty  
(1-Year Limited Warranty from the date of purchase). Customer is required to  
provide invoice as purchase evidence.  
**Network conditions and environmental factors as well as network overhead can  
lower actual data throughput rate.  
Copyright © 2011 AirLink101®. All rights reserved. AirLink101, the stylized  
AirLink101® logo, specific product designations, and all other words and logos  
that are identified as trademarks and/or service marks are, unless noted  
otherwise, the trademarks and service marks of AirLink101®. All other product or  
service names are the property of their respective holders. AirLink101 products  
are protected under numerous U.S. and foreign patents and pending applications,  
mask work rights, and copyrights.  
12  
 

Acer Computer Monitor P215H User Manual
Advantech Network Card EKI 2525P User Manual
Agilent Technologies Power Supply 6625A User Manual
Alpine CD Player CDA 7892E User Manual
Alpine Stereo Amplifier MRD M500 User Manual
Amana Refrigerator ABB2222FEB11 User Manual
American Standard Indoor Furnishings 034782 XXX0A User Manual
Audiovox Remote Starter 128 8128 User Manual
Axis Communications Security Camera AXIS Q8414 LVS User Manual
Eureka Tents Tent Chrysalis User Manual